Differences

This shows you the differences between two versions of the page.

--- getting_started:tutorials:oneaxis_bbb [2019/10/12 19:28] – created graf
+++ getting_started:tutorials:oneaxis_bbb [2019/10/14 17:21] – [Enable Signal] graf
@@ Line 1: / Line 1: @@
-====== Headline ======
+====== Experimental Setup with a Beaglebone Blue Board ======
+Use a [[https://wiki.ntb.ch/infoportal/embedded_systems/ti_sitara_am335x/beaglebone_blue/start|Beaglebone Blue]]. Connect all the necessary signals according to your hardware configuration file.
-  * A [[https://wiki.ntb.ch/infoportal/embedded_systems/ti_sitara_am335x/beaglebone_blue/start|Beaglebone Blue]] board together with the appropriate EEROS hardware wrapper, see [[eeros_architecture:hal:hardware_libraries#beaglebone_blue|Hardware Wrapper Libraries]]. Please follow the instructions in [[https://wiki.ntb.ch/infoportal/software/linux/beagleboneblue]] to install the necessary toolchain before you install EEROS.
+===== Analog Output =====
-  * Our cb20 controller board ([[http://wiki.ntb.ch/infoportal/embedded_systems/imx6/cb#cb20_board|]] together with [[http://www.flink-project.ch|]] and the appropriate EEROS hardware wrapper, see [[eeros_architecture:hal:hardware_libraries#flink|]].
+There are 4 connectors denoted with //DC Motors//. Connect number 1 with the motor. Before testing plug in the 12V DC power supply or the Li-Po battery, otherwise the motors won't run. ssh into the Beaglebone blue board and run
+<code>
+debian@beaglebone:$ rc_test_motors -m 1 -d 1
+</code>
+//-m 1// selects the first motor while //-d 1// specifies a duty cycle of 1. The motor should run in positive direction. If the motor turns in the opposite direction, change the + and - wire of the motor. You can stop the program by pressing ''Ctrl-C''. The test program is located in ///usr/bin// and can be run from anywhere.
-Connect all the necessary signals according to your hardware configuration file, notably
+===== Enable Signal =====
-  * analog output and enable signal to the motor controller
+On the Beaglebone blue we do not use a motor controller and therefore, we do not use this signal. However, we put the signal onto the green led on the board.
-  * encoder outputs (A/B signals) to the decoder inputs
-  * motor controller ready signal to a digital input
-  * emergency button to a digital input
-IMPORTANT Make sure that a positive voltage on the motor leads to the encoder counting upwards. If the opposite is the case, either change the cables or change the hardware configuration file. \\
+===== Encoder Inputs =====
-IMPORTANT On the beaglebone blue board, you don't need a motor controller. Hence, you do not need the enable signal. Tie the ready signal to logic one.
+There are 4 connectors denoted with //4 Quadrature encoder inputs//. Connect number 1 with your encoder. Make sure that your encoder works with 3.3V as delivered by this connector. Test the encoder with
+<code>
+debian@beaglebone:$ rc_test_encoders
+</code>
+Turning the motor in positive direction must lead to the encoder counting upwards. If not, change the A and B signal.
+===== Ready Signal =====
+The ready signal signals to the controller that the motor controller has powered up. As there is no external motor controller on the Beaglebone blue we simply put this signal on a digital input pin which is connected to the on board push button //Mode//.
+===== Emergency Signal =====
+The emergency signal is used to bring the application in a safe mode. We put this input signal on a digital input pin which is connected to the on board push button //Pause//. Later when the application runs
+  * emergency button to a digital input